模具专业英语

一、入水：gate

进入位：　gate location

水口形式：gate type

大水口：edge gate

细水口： pin-point gate

水口大小：gate size

转水口：　switching runner/gate

 唧嘴口径：　sprue diameter

二、流道: runner

热流道：　hot runner,hot manifold

热嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圆形流道：round(full/half runner

流道电脑分析：mold flow analysis

流道平衡:runner balance

热嘴：　hot sprue

热流道板：hot manifold

发热管：cartridge heater

探针: thermocouples

插头：　connector plug

插座： connector socket

密封/封料： seal

三、运水：water line

喉塞：line lpug

喉管：tube

塑胶管：plastic tube

快速接头：jiffy quick connector plug/socker

四、模具零件：　mold components

三板模：3-plate mold 二板模：2-plate mold

边钉/导边：leader pin/guide pin

模具专业英语边司/导套：bushing/guide bushing

中托司：shoulder guide bushing

中托边L：guide pin

顶针板：ejector retainner plate

托板：　support plate

螺丝： screw

管钉：dowel pin

开模槽：ply bar scot

内模管位：core/cavity inter-lock

顶针：　ejector pin

司筒：ejector sleeve

司筒针：ejector pin

推板：stripper plate

缩呵：movable core,return core core puller

扣机（尼龙拉勾）：nylon latch lock

斜顶：lifter

模胚（架）： mold base

上内模：cavity insert

下内模：core insert

行位（滑块）： slide

镶件：insert

压座/斜鸡：wedge

耐磨板/油板：wedge wear plate

压条：plate

撑头: support pillar

唧嘴： sprue bushing

挡板：stop plate

定位圈：locating ring

锁扣：latch

扣鸡：parting lock set

推杆：push staff

栓打螺丝：S.H.S.B

 顶板：eracuretun

活动臂：lever arm

分流锥：spure sperader

水口司:bush

垃圾钉：stop pin

隔片：buffle

弹弓柱：spring rod

弹弓:die spring

中托司：ejector guide bush

中托边：ejector guide pin

镶针：pin

销子：dowel pin

波子弹弓：ball catch

喉塞: pipe plug

锁模块：lock plate

斜顶：angle from pin

斜顶杆：angle ejector rod

尼龙拉勾：parting locks

活动臂：lever arm

复位键、提前回杆：early return bar

气阀：valves

斜导边：angle pin

术语：terms

承压平面平衡：parting surface support bal-ance

模排气：parting line venting

回针碰料位：return pin and cavity interfer-ence

模总高超出啤机规格：mold base shut hight

模具专业英语顶针碰运水：water line interferes withejec- tor pin

料位出上/下模：part from cavith (core) side

模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.

不准用镶件： Do not use (core/cavity) insert

用铍铜做镶件： use beryllium copper insert 初步（正式）

模图设计：preliinary (final) mold design

反呵：reverse core

弹弓压缩量：spring compressed length

稳定性好：good stability,stable

强度不够：insufficient rigidity

均匀冷却：even cooling

扣模：sticking

热膨胀：thero expansion

公差：tolorance

铜公(电极）：copper electrod

在模板上及行位斜面的硬块:wear plates under slides and on back of slide lock